B-serie

The RAP-SB-238U, composite diamond base, contains a 0.75" high strength composite ball connected at right angles to a 1.25" x 2.5" inch diamond plate. The base has two holes 1.912" from center to center, positioned at both ends of the diamond base.

RAM Composite 2" x 1.7" Base with 1" Ball that Contains the Universal AMPs Hole Pattern for the Garmin zumo, TomTom Rider & Urban Rider The RAP-B-347U base consists of a 1" diameter rubber ball connected at right angles to a 2" x 1.7" square base. The base has four pre-drilled holes at each corner, making the universal 1.5 x 1.188 (hole spacing) AMPS hole pattern.

The RAP-B-202U contains a 1" diameter rubber ball connected to a flat 2.5" diameter base. This mount has pre-drilled holes, including the universal AMPS hole pattern.

The RAP-B-294U consists of a 1" diameter ball with female PVC slip pipe socket. The socket can connect to any RAM PVC pipe and can be permanently fastened using electrical tape or PVC pipe cement. Intended for light duty use. Not intended for use in vehicle interiors or high temperature environments.

The RAM-HOL-UN7-BALLU consists of a 1" diameter rubber ball and hardware for attaching to the back of the RAM-HOL-UN7U cradle.

The RAM-B-238U consists of a B size 1" diameter rubber ball on a 2.43" x 1.31" diamond plate. The plate has two holes 1.912" from center to center, matches the industry standard AMPS hole pattern and will connect to a large variety of RAM mounts and third party cradles.

The RAM-B-347U base consists of a 1" diameter rubber ball connected at right angles to a 2" x 1.7" square base. The base has four pre-drilled holes at each corner, making the universal 1.5 x 1.188 (hole spacing) AMPS hole pattern.

The RAM-B-202U consists of a B Size 1" diameter rubber ball connected to a flat 2.5" diameter plate. This mount has pre-drilled holes, including the universal AMPs hole pattern.

The RAM-B-237U, universal camera and camcorder base, consists of a 1" diameter rubber ball, connected to a 1/4"-20 camera thread. The male thread matches most standard camera and camcorder female threads found on the bottom of the camera.

Have an M8 by 25, 30, or 35mm handlebar bolt? The RAM-B-367U will replace that bolt with a standard ball-mount to put just about anything there! Included with Purchase: (1 QTY) 1" Rubber ball (1 QTY) M8 x 55 bolt (1.25 thread pitch) (1 QTY) M8 x 60 bolt (1.25 thread pitch) (1 QTY) M8 x 65 bolt (1.25 thread pitch) Compatible Motorcycles: Any motorcycle which employs an 8mm bolt or smaller on its structure. A smaller bolt can be used, though the load capacity decreases with the bolt size.

RAM Rail Base with 1" Ball (No Hardware) Part# RAM-B-231NHU

RAM 1" Track Ball™ with T-Bolt Attachment Part# RAP-B-354U-TRA1 The RAM Track Ball is made up of a B size 1" rubber ball molded to a high strength composite base, a rubber friction washer and a stainless steel T-bolt for sliding into virtually any track system. Simply insert or slide the Track Ball into your track and twist the ball clockwise to tighten in place. Twist counterclockwise to loosen or adjust the ball. T-Bolt Dimensions: .48" x .95"

GoPro® cameras have reinvented how we capture some of the most exciting moments in our lives. Nearly two decades ago, RAM began reinventing mounting systems so that enthusiasts could use their cameras and video equipment like never before. RAM is proud to offer a sleek new adapter that will bring two revolutionary product lines together and open up a world of possibilities. While the GoPro® line of mounting accessories is nothing to scoff at, the diversity of the RAM product line is simply unmatched. Dream it. Live it. Capture it. RAM Mounting Systems and GoPro® make it possible to truly “Be a HERO™”. The RAP-B-202U-GOP1 consists of a 1" diameter rubber ball, connected to a custom GoPro® adapter. The adapter attaches directly to the under-side of the camera, replacing the factory mounting bracket.

The RAP-B-201U, composite standard double socket arm, has a socket at both ends that accommodates 1" ball bases. A single spring inside the arm opens the end sockets, allowing you to pivot the ball and socket connection. This socket technology allows for almost infinite adjustment and perfect viewing angles. Dimensions: Overall Length: 3.69" Socket-To-Socket Length: 3"

The RAM-B-201U-A, Short length double socket arm, has a socket at both ends that accommodates B Size 1" balls. RAM's socket technology allows for almost infinite adjustment to achieve the perfect viewing angle. Dimensions: Overall Length: 2.38" Socket-To-Socket Length: 1.75" NOTE This product does not include the pin spring

The RAM-B-272U consists of a 1" diameter ball and base with 9mm hole. This part is often used on motorcycles, attaching to the mirror frame, the main brand of bike for the RAM-B-272U is BMW.

The RAM-B-231-1U a 1" rubber ball designed to sit at right angles to the mounting rail. The stainless steel coated metal u-bolt accommodates rails in diameter from 1" to 1.25" in diameter. The base also includes black cover caps to be placed over the exposed ends of the u-bolt.

The RAM-B-202U-225 contains a 1" diameter rubber ball connected to a rectangular plate with a 4-hole pattern of 1.5" x 2" center to center. Overall plate dimensions are 2" x 2.5".

The RAM-B-309-1U connects to your handlebar clutch/brake clamp, left or right side, and holds one 1" diameter mounting ball. The base fits the control clamps on your motorcycle with 40mm x 6mm stainless steel hardware, provided in the kit. To see if the RAM-B-309-1U base will mount to your motorcycle, check the hole spacing of the base against your clutch/brake reservoir. The holes centers have a minimum width of 0.94" and a maximum of 1.58".

The RAM-B-231ZU consists of a B size 1" rubber ball designed to sit at right angles to the mounting rail. The zinc coated metal u-bolt accommodates rails in diameter from 0.5" to 1.25" in diameter. Included are black cover caps to be placed over the exposed ends of the u-bolt and a composite adapter that can narrow the rail to a minimum width of 0.5". U-Bolt Dimensions: Accommodates rails from 0.5" to 1.25" in diameter.

The RAM® Motorcycle Fork Stem Base is one of the cleanest and most popular solutions for mounting your device cleanly on the center of your bike. This part is designed to fit into the cylindrical bore wall of fork stems and will work with stems that measure from 12 - 33mm (.5” – 1.29”).

The RAM-B-224-1U consists of a 3.3" diameter suction cup twist lock base that is connected to the (RAM-B-238U), diamond base with B size 1" rubber ball. The suction cup is designed to have an extra strong hold on any smooth non-porous surface, but for best result, mount the suction cup on a glass or non-porous plastic surface.

The RAM-B-201-ALA1-KRU, STANDARD length double socket arm with retention knob, has a socket at both ends that accommodates 1" ball bases. A single spring inside the arm opens the end sockets, allowing you to pivot the ball and socket connection. The knob extension allows for easy adjustment of the mount and prevents over loosening of the knob. This socket technology allows for almost infinite adjustment and perfect viewing angles. Dimensions: Overall Length: 3.69" Socket-To-Socket Length: 3"

The RAM® Torque™ handlebar and rail mounting base has a 1” rubber ball and accommodates bars ¾” to 1” in diameter. Sizing inserts are included to provide a snug fit and protection of the rail. The mount utilizes nylon-insert locknuts to prevent loosening in high vibration environments. Mounting Base Dimensions: Accommodates rails 0.75" to 1" in diameter.

The RAM® Torque™ bar mount has a 1” rubber ball and accommodates rails 3/8” to 5/8” in diameter. Sizing inserts are included to provide a snug fit and protection of the rail. The mount utilizes nylon-insert locknuts to prevent loosening in high vibration environments. The RAM-B-408-37-62U allows for mounting to scooter mirror rails as well as vehicle headrests and other round rails within the stated dimensions. Rail Mount Dimensions: Accommodates rails 3/8" to 5/8" in diameter.

The RAM-B-230U, double ball joiner, consists of a 1" rubber ball on both ends that allow the connection of two 1" socket arms. When measured from ball center to ball center the arm length is 1.75". This mount is ideal if your mount arm is just too short.